You can now manage the Cisco MGX 8260 media gateway using a Telnet session or Cisco WebViewer. Management Interfaces Configuration (lsmgips) The following example shows a sample output: = Step 5 Check the IP configuration settings using the lsmgips command. Step 4 Set the IP address and mask for the in-band management interface (via a SCC Fast Ethernet port) using the chibip command.įor example, with a system IP address of 10.15.28.20 and a 24-bit subnet mask, enter the following command and press Return: chibip 10.15.28.20 255.255.255.0 Step 3 Specify the IP address of a gateway router for management traffic using the chgw command. Step 2 Set the IP address and mask for the secondary management interface using the chsysip2 command.įor example, with a system IP address of 10.15.27.20 and a 24-bit subnet mask, enter the following command and press Return: chsysip2 10.15.27.20 255.255.255.0 Step 1 Set the IP address and mask for the primary management interface using the chsysip1 command.įor example, with a system IP address of 10.15.26.20 and a 24-bit subnet mask, enter the following command and press Return: chsysip1 10.15.26.20 255.255.255.0 To configure IP addresses, follow these steps: Note For additional information, refer to the Cisco MGX 8260 Command Line Interface Guide. The MGX 8260 must be equipped with an SCC-FE back card to use this option.īefore performing the following procedure, obtain IP addresses, subnet masks, and gateway addresses for the Cisco MGX 8260 media gateway from your system administrator. The in-band IP address creates a virtual port for management over one of the Fast Ethernet (100BASE-TX) VoIP ports. Otherwise, just set one system IP address. If your system uses redundant subnetworks for system management, set both IP addresses. The system management interface supports two IP addresses, one for each 10BASE-T Ethernet management port. To communicate with the Cisco MGX 8260 media gateway over a network, set up IP addresses for the following types of network management: The Cisco MGX 8260 media gateway displays a command line prompt. Step 3 At the Password prompt, enter cisco. Step 2 At the User Id prompt, enter SuperUser. Note The active SCC is indicated by the card LED being illuminated green. Step 1 With Hyper Terminal running and a connection made to the active SCC console, enter two carriage returns to obtain a login prompt. Note Before putting the MGX 8260 in service, replace this default account with a unique one. Use the default account to initialize the node. Logging Inīefore you can configure the Cisco MGX 8260 media gateway, you must log in as a user with the privilege to change system parameters. You initialize the equipment using the command line interface during a console session. This procedure explains how to prepare a new system for basic operation by initializing the IP addresses and node parameters. You are now ready to log onto the Cisco MGX 8260 media gateway and initialize the equipment. (Refer to "Cable and Connector Reference.") Step 8 If you have not already done so, connect an EIA/TIA-232 cable between the MGX 8260 console port of the active SCC and the PC. You only have to perform this procedure once on a specific PC. Step 7 Click File then click Save to save your terminal emulation settings for future use. Step 6 Click the Settings tab and then select VT100 from the Emulation drop-down list. Step 5 In the Hyperterminal window, select File > Properties. Step 4 In the COM Properties dialog box, set bits per second to 9600, data bits to 8, parity to none, Step 3 In the Connect Using field, select the desired COM port and then click OK. Step 2 In the Name field, enter a short name and then click OK. The Connection Description dialog box opens. Step 1 From the Start menu, select Start > Programs > Applications > Hyperterminal To start terminal emulation on Windows 95 or NT, follow these steps: Note This procedure varies somewhat for different operating systems. The Cisco MGX 8260 console port has a standard EIA/TIA-232, DCE serial port. For later sessions, simply double-click the HyperTerminal icon for the configuration you defined. You only perform the HyperTerminal setup procedure once for a specific PC. The procedure for starting HyperTerminal varies by PC, so your startup procedure may differ somewhat from the one described in this chapter. This section describes how to set up the MGX 8260 using Microsoft Windows HyperTerminal. A laptop PC running terminal emulation software works efficiently for this task. Setting up the MGX 8260 IP addresses requires a VT100-compatible terminal or PC connected to the console port. This chapter describes how to set up a management console and configure MGX 8260 media gateway parameters. Table of Contents Starting the Media Gateway
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |